Category Archives: Sports

Learn How to Clear the Lines for a Swimming Pool

Posted on by
Reply

How to Clear the Lines for a Swimming Pool thumbnail

To Clear the Lines for a Swimming Pool, you have to plug in a shop vacuum or Mighty Vac. You need to Use one that has a 2.75-horsepower motor for enough power to blow out the lines. You must ensure the vacuum is plugged into an outlet that is close to the pool skimmer. After that, Connect the vacuum to the skimmer line, Turn it on and Blow air through the skimmer, piping as well as equipment. Then, Look into the water.

Next, Insert expansion plugs into the spot where the return lines enter the pool.

Learn How to Treat Paecilomyces Lilacinus in a Swimming Pool

Posted on by
Reply

How to Treat Paecilomyces Lilacinus in a Swimming Pool thumbnail

To Treat Paecilomyces Lilacinus in a Swimming Pool, you have to fill a 5-gallon bucket with pool water. You need to put on gloves to protect your hands. You must pour a granulated calcium hypochlorite-based shock treatment into the bucket slowly. You should Stir the solution well and agitate it for at least sixty seconds until the shock treatment dissolves. After that, turn on the pool’s filtration system and pour the solution slowly in front of the return line fitting.

If it is available undissolved granules at the bottom of the bucket, you can add more pool water, agitate and slowly pour into the pool. Then, Keep the pump on to continuously circulate the water. Next, clean the walls of the pool with a stiff-bristled brush. You have to Work from one end to the other until the entire pool is scrubbed. Forth, vacuum the floor of the pool. You need to Work from the outside of the pool in circles until you reach the very center. After that, pour a commercial algaecide formulated to kill pink algae into the pool.

Continue reading →

Learn How to Re-Plaster a Swimming Pool

Posted on by
Reply

How to Re-Plaster a Swimming Pool thumbnail

To Re-Plaster a Swimming Pool, you have to Turn off the pump and empty the pool. You need to Scrub the entire surface with detergent. You must let the walls to dry. After that, Scrub with a wire brush to loosen flaky areas. You should pry particularly bad areas off with a hammer and putty knife or chisel.

You can Sand all rough areas with using coarse grit sandpaper until the entire surface is smooth. Then, you must Acid wash the pool. You have to use protective goggles, face mask as well as clothing for this step. You need to Mix the acid with water based on the manufacturer’s directions and brush Muriatic acid over the entire surface of the pool, one section at a time. When it has stopped reacting with the existing concrete, you must hose it off immediately to prevent it from weakening the concrete.

Continue reading →

Learn How to Defoam a Swimming Pool

Posted on by
Reply

How to Defoam a Swimming Pool thumbnail

To Defoam a Swimming Pool, you have to remove as much foam as possible with a pool skimmer. You need to Use a garden hose to spray foam in the center of the pool toward the edges to make it easier to remove. After that, clean your pool filter’s cartridge to remove any lotions and conditioners that may have built up as well as create foam. Then, Test the pool’s calcium hardness levels with a pool test kit. Next, Add calcium chloride or any other calcium-increasing product in small increments with following the instructions on the package.

You must turn on your pool’s filter to disperse the chemical and retest after a few hours. You should continue to add calcium until the pool’s levels are in the ideal range. Forth, add a copper-based Algicide with following the instructions on the package to reduce foam-producing algae. After that, check all hoses, connections and filters for air leaks that can exacerbate an existing foam problem. You can Repair or replace any bad equipment.

Continue reading →

Learn How to Weigh Down Balloons in a Swimming Pool

Posted on by
Reply

How to Weigh Down Balloons in a Swimming Pool thumbnail

To Weigh down Balloons in a Swimming Pool, you have to Place the narrow end of the funnel into the mouth of the empty balloon. After that, Pour sand into the balloon until it is approximately one-quarter of the way filled with sand. Then, Use the balloon pump to blow up the balloon to your desired size. Next, Tie the mouth of the balloon closed quickly as you can to prevent air from escaping. Forth, put the balloon in the pool.

Learn How to Dig the Deep End for a Swimming Pool

Posted on by
Reply

How to Dig the Deep End for a Swimming Pool thumbnail

To Dig the Deep End for a Swimming Pool, you have to draw out the desired shape and size of the pool with paper and a pencil. You need to Use graph paper to properly draw the pool to scale. After that, spray paint the soil to mark the desired outline of the pool. You must hammer stakes into the ground to frame the outline. You should tie a string around each of the stakes.

Then, excavate the area within the stakes with a backhoe excavator. You can check the bottom layer of soil with a laser level to ensure the depth is even. You have to Move the backhoe to the area of the pool intended for the deep end. Next, Dig down to a depth of between eight to nine feet lower than the other section of pool for the deep end. You need to Add an additional three feet to this depth for the flooring and foundation.

Continue reading →

Learn How to Do Fake Rocks for a Swimming Pool

Posted on by
Reply

To Do Fake Rocks for a Swimming Pool, you have to Plan the layout of the rocks you will create. If you plan on building large boulders, you need to build the mold near the finished location of the boulder as even hollow rocks will be heavy. After that, cut pieces of Styrofoam to make the shape of the rock. You must select one of two ways to create the mold. You should carve a large block of Styrofoam into the shape you want.

You can assemble the layers of Styrofoam and secure each piece to the next with wire pins. Then, Cover the mold with steel mesh to secure the mesh with wire pins. Next, Cut sections of chicken wire that can cover the rock from side to side. You have to wrap the sections around the mold one at a time. You need to secure each section to the next with wire pins or with wrapping the chicken wire around the next piece.

Continue reading →

Learn How to Wire a Wet Border Swimming Pool

Posted on by
Reply

How to Wire a Wet Border Swimming Pool thumbnail

To Wire a Wet Border Swimming Pool, you have to Contact your local building department to get a permit. After that, shut off the electricity at the main switch box. If the GFCI circuit breaker is installed inside the house, you need to cut a small hole in the exterior cladding and install a weatherproof elbow. Then, Dig an 18-inch deep trench with a shovel to extend from the house to the pool equipment. Next, Install conduit from the GFCI circuit breaker box attached to the house through the rigid weatherproof elbow and extension and down into the trench.

You must check your local building department for details. You should install all conduit connectors and circuit breakers as detailed in the plan that was prepared for the electrical permit. Forth, String the electrical cable through the conduit and into the trench to extend from the house to the pool equipment. You can connect electrical cable to the circuit breaker and the pool equipment. After that, Contact your local building department for a site inspection before filling in the trench if required.

Continue reading →

Learn How to Make a Fake Rock Facade in a Swimming Pool

Posted on by
Reply

How to Make a Fake Rock Facade in a Swimming Pool thumbnail

To Make a Fake Rock Facade in a Swimming Pool, you have to drain the area of the pool where the facade will be installed if along the water line. You need to allow the surface of the facade dries and sand it down thoroughly with rough-grit sandpaper. You must wipe it cleans. After that, spread waterproof-paper-backed lath over the facade area. You should drill holes through the lath and into the masonry behind it with using a hammer drill.

You can Drill 3-inch holes and set a masonry screw with using a large washer in each hole and tightening each one completely. You have to Space these screws every twelve inches in a grid across the lath. You need to overlap all lath seams by six inches. Then, Apply waterproof mortar to the lath to a depth of 1/2 inch using a trowel. You must cut off a piece of lath and scrape the mortar with it after the mortar has set for twenty minutes.

Continue reading →

Learn How to Attach the Band on Swimming Goggles

Posted on by
Reply

How to Attach the Band on Swimming Goggles thumbnail

To Attach the Band on Swimming Goggles, you have to find the band loop on your goggles. After that, lay your goggles face down and place the strap over them. You must make sure the strap lies flat and is not twisted. Then, Push one end of the strap through the band loop from the back of the goggles. Next, Pull the strap through a few inches and loop it back through itself.

Forth, repeat this process on the other side.